Carrier KGANP5201VSP Manuel d'instructions télécharger pdf (Page 23)

FIREANDEXPLOSIONHAZARD

Failureto follow this warning could result in personal injury

and/or death.

NEVER test for gas leaks with an open flame. Use a

commercially available soap solution made specifically for

the detection of leaks to check all connections. A fire or

explosion may result causing property damage, personal

injury or loss of life.

RISQUE D'EXPLOSION ET D'INCENDIE

Le fair de ne pas suivre cet avertissement pourrait entra_ner des

dommages corporels et / ou la mort.

Ne jamais examiner pour les fuites de gaz avec une flamme

vive. Utilisez plut6t un savon fair specifiquement pour la

d6tection des fuites de gaz pour verifier tousles connections.

Un incendie ou une explosion peut entrainer des dommages

mat6riels, des blessures ou la mort.

MODIFY PRESSURE SWITCH WIRING

UNIT OPERATION HAZARD

Failure to follow this caution may result in unit damage or

improper operation.

Label all wires prior to disconnection when servicing

controls.

D'EQUIPEMENT D'OPERATION

Toute erreur de cfiblage peut _tre une source de danger et de

panne.

Lors des op6rations d'entretien des commandes, 6tiqueter

tousles fils avant de les d6connecter.

1. Locate the orange wire in the kit with an insulated straight

female spade terminal and an insulated straight male ter-

minal on the other end.

2. Connect the female terminal to a terminal on the Low Gas

Pressure Switch.

3. Locate the orange wire in the kit with an insulated straight

female spade terminal and an insulated female flag termin-

al on the other end.

4. Connect both straight female terminals of the orange wires

to the terminals on the Low Gas Pressure Switch.

5. Disconnect orange wire from low-heat pressure switch

LPS on inducer housing.

6. Connect the orange wire from the Low Heat Pressure

Switch to the orange wire with the insulated male spade

terminal.

7. Connect the orange wire from the Low Gas Pressure

Switch to the terminal on the Low Heat Pressure Switch.

8. Route orange wires along wire harness. If possible, secure

with wire tie provided in kit.

CHECK INLET GAS PRESSURE

SW4

Outside Air Thermi,'

SW3 Continuous

(CF) airflow setup

switches CF 1 through

CF 3 _-_--_

Communication

24 VAC

HUM Output

(O.5AMP

SW4

[]

_I=_ PL9

Connection " P,7 ABeD,

._< _ SW3

ModelPlug_ g__ _i_:_ _11_')11_,_11(\_11

/_21 _ W2 Yt DHUM

SW2

Setup Switches SWl,

1 thru 8

SW2 A/C Air Flow

Setup Switches

AC 1 through AC 3

Al1471

Fig. 45 - Furnace Control

[]NIT DAMAGE HAZARD

Failure to follow this caution may result in unit damage.

DO NOT operate furnace more than one minute to check

inlet gas pressure, as conversion is not complete at this time.

NOTE: This kit is to be used only when inlet gas pressure is

between ll.0-in. W.C. and 13.6-in. W.C.

1. Verify manometer is connected to inlet pressure tap on gas

valve.

2. Turn on furnace power supply.

3. Turn gas supply manual shutoff valve to ON position.

4. Turn furnace gas valve switch to ON position.

5. Turn Setup Switch SWI-2 on furnace control ON (see

Fig. 45).

6. Jumper R-W/WI and R-W2 thermostat connections on

control.

7. When main burners ignite, confirm inlet gas pressure is

between ll.0-in. W.C. and 13.6-in. W.C.

8. Remove jumper across R-W/WI and R-W2 thermostat

connections to terminate call for heat.

9. Turn furnace gas valve switch to OFF position.

10. Turn gas supply manual shutoff valve to OFF position.

11. Turn off furnace power supply.

12. Remove manometer.

13. Apply pipe dope sparingly to end of inlet gas pipe plug

and install into unused end of 1/8 in. tee. Use a small

1 2 ... 18 19 20 21 22 23 24 25 26

Commentaires sur ces manuels

Pas de commentaire

Carrier KGANP5201VSP Manuel d'instructions Page 23

Commentaires sur ces manuels

Produits connexes et manuels pour Chauffe-eau et chaudières Carrier KGANP5201VSP