Carrier KGANP5201VSP Manuel d'instructions télécharger pdf (Page 20)

CONVERSION KiT RATING PLATE CARRIER CORPORATION

THiS APPLIANCE HAS BEEN CONVERTED TO USE PROPANE GAS FOR FUEL, REFER TO KiT iNSTRUCTiONS FOR CONVERSION

PROCEDURES. USE PARTS SUPPLIED BY CARRIER CORPORATION AND iNSTALLED BY QUALiFiED PERSONNEL.

SEE EXiSTiNG RATING PLATE FOR APPLIANCE MODEL NO. AND iNPUT RATING.

NOTE: Furnace gas input rate on rating plate is for installations up to 2000 ft. (610m) above sea level In U,S.A. the input rating for altitudes above 2000 ft, (610m) must

be derated by 4% for each 1000 ft. (305m) above sea [eveL in Canada the input rating must be derated by 10% for aRitudes of 2000 ft. (610m) to 4500 ft. (1372m) above sea [eveL

KiT NO.: KGANP5201VSP FUEL USED: PROPANEGAS iNLETPRESSURE (rain- raax): 11.0- 13.6 in.wc

(SUPERSEDES:KGANP4601ALL,KGANP4101ALL,KGANP4001ALL,KGANP3001ALL,KGANP2901ALL)

ALTITUDE OF INSTALLATION (FT. ABOVE SEA LEVEL) U.S.A. *

APPLIANCE

0 2001 * 3001 4001 5001 6001 7001 8001 9001

MODELS to 2000 to 3000 to 4000 to 5000 to 6000 to 7000 to 8000 to 9000 to 10000

Orifice 55 1.30mm 1.30ram i1.25mm 1.25mm 1.25mm 56 56 56

No,

58CVA, 58CVX Manifold Pressure I_

,o,o oleo[o olo lo11.oI

PG8JVA, PGSMVA LOW 5.8 I 5.3 5.0 5.5 5.2 4.9 5.7 5.2 4.8

_. * For Canadian installations from 2000 to 4500 ft. (610rato 1373ra) use U.S.A. column2001 to 3000 ft. (611rato 914ra). 337704-204REV.D

Al1636

Fig. 37 - Conversion Kit Rating Plate

1337932-7021

CONTAINS: QTY

PART # DESCRIPTmON

328456-401 BIT, DRILL 1

327593-401 SCREW 7

REQUIRED FOR CONVERSION OF

NON CONDENSING GAS FURNACE

TO PROPANE GAS.

Fig. 38 - Gas Conversion Kit

\ i

--_l 1-9/16"

39.7 ram

Fig. 39 - Mixer Screw Location

A11397

Drill out with

5/64" drill bit.

A06432

Fig. 40 - Igniter Position - Side View

5/16"

7.9mm

A05025

REINSTALL BURNER ASSEMBLY

To reinstall burner assembly:

1. Attach flame sensor to burner assembly.

2. Install HSI and bracket to burner assembly.

3. Insert one-piece burner in slot on sides of burner box and

slide burner back in place.

4. Reattach HSI wires to HSI.

5. Verify igniter to burner alignment.

6. For Silicon Nitride igniters, see Fig. 40 and 41.

7. For Silicon Carbide igniters, see Fig. 42.

8. Re-attach Flame sensor wire to Flame Sensor.

1 2 ... 15 16 17 18 19 20 21 22 23 24 25 26

Commentaires sur ces manuels

Pas de commentaire

Carrier KGANP5201VSP Manuel d'instructions Page 20

Commentaires sur ces manuels

Produits connexes et manuels pour Chauffe-eau et chaudières Carrier KGANP5201VSP