Carrier KGANP5201VSP Manuel d'instructions télécharger pdf (Page 16)

D'EQUIPEMENT D'OPERATION

Toute erreur de cfiblage peut _tre une source de danger et de

panne.

Lors des op6rations d'entretien des commandes, 6tiqueter

tous les ills avant de les d6connecter.

1. Disconnect orange wire from low-heat pressure switch

LPS on inducer housing.

2. Connect the orange wire from the Low Heat Pressure

Switch to the orange wire with the insulated male spade

terminal.

3. Connect the orange wire from the Low Gas Pressure

Switch to the terminal on the Low Heat Pressure Switch.

4. Route orange wires along wire harness. If possible, secure

with wire tie provided in kit.

CHECK INLET GAS PRESSURE

UNIT DAMAGE HAZARD

Failure to follow this caution may result in unit damage.

DO NOT operate furnace more than one minute to check

inlet gas pressure, as conversion is not complete at this time.

NOTE: This kit is to be used only when inlet gas pressure is

between ll.0-in. W.C. and 13.6-in. W.C.

1. Verify manometer is connected to inlet pressure tap on gas

valve.

2. Turn on furnace power supply.

3. Turn gas supply manual shutoff valve to ON position.

4. Turn furnace gas valve switch to ON position.

5. Turn Setup Switch SWI-2 on furnace control ON (see

Fig. 31).

6. Jumper R-W/W1 and R-W2 thermostat connections on

control.

7. When main burners ignite, confirm inlet gas pressure is

between ll.0-in. W.C. and 13.6-in. W.C.

8. Remove jumper across R-W/WI and R-W2 thermostat

connections to terminate call for heat.

9. Turn furnace gas valve switch to OFF position.

10. Turn gas supply manual shutoff valve to OFF position.

11. Turn off furnace power supply.

12. Remove manometer.

13. Apply pipe dope sparingly to end of inlet gas pipe plug

and install into unused end of 1/8 in. tee. Use a small

back-up wrench on tee when tightening gas inlet pipe

plug. (See Fig. 13.)

CHECK FURNACE AND MAKE ADJUSTMENTS

FIRE AND EXPLOSION HAZARD

Failure to follow this warning could result in personal iniury

and/or death.

NEVER test for gas leaks with an open flame. Use a

commercially available soap solution made specifically for

the detection of leaks to check all connections. A fire or

explosion may result causing property damage, personal

injury or loss of life.

RISQUE D'EXPLOSION ET D'INCENDIE

Le fait de ne pas suivre cet avertissement pourrait entra_ner des

dommages corporels et / ou la mort.

Ne jamais examiner pour les fuites de gaz avec une flamme

vive. Utilisez plut6t un savon fair specifiquement pour la

d_tection des fuites de gaz pour verifier tous les connections.

Un incendie ou une explosion peut entrainer des dommages

materiels, des blessures ou la mort.

SW4

Outside Air Thermistor_

_F_ CrflnotiwnU;_uSpFan_

switches CF 1 through

CF 3

Communication

_I_ SW4

[]

_I=_PL9

Connecton--

24 VAC

HUM Output

(O.5AMP

Setup Switches SWl,

1 thru 8

ModelPlug ____ _-I[1 _'!_i I_]_

/_ /_:21 _ W2 Yt DHUM

SW2

SW2 A/C Air Flow

Setup Switches

AC 1 through AC 3

Fig. 31 - Furnace Control

Al1471

FIRE, EXPLOSION, ELECTRICALSHOCK

HAZARD

Failure to follow this warning could result in personal

iniury, death or property damage.

Gas supply MUST be shut off before disconnecting

electrical power and proceeding with conversion.

ELECTRICAL SHOCK, FIRE OR EXPLOSION

HAZARD

Failure to follow this warning could result in personal

iniury, death or property damage.

Before installing, modifying, or servicing system, main

electrical disconnect switch must be in the OFF position and

install a lockout tag. There may be more than one

disconnect switch. Lock out and tag switch with a suitaMe

warning label. Verify proper operation after servicing.

1 2 ... 11 12 13 14 15 16 17 18 19 20 21 ... 25 26

Commentaires sur ces manuels

Pas de commentaire

Carrier KGANP5201VSP Manuel d'instructions Page 16

Commentaires sur ces manuels

Produits connexes et manuels pour Chauffe-eau et chaudières Carrier KGANP5201VSP