Carrier KGANP5201VSP Manuel d'instructions télécharger pdf (Page 13)

ORIFICE SELECTION/DERATE

[]NIT DAMAGE HAZARD

Failure to follow this caution may result in unit damage.

DO NOT re-drill burner orifices. Improper drilling may

result in burrs, out-of-round holes, etc. Obtain new orifices

if orifice size must be changed. (See Fig. 22.)

In Canada, the input rating must be derated by 5 percent for

altitudes of 2000 ft. to 4500 ft. (610 M to 1372 M) above sea

level.

The Conversion Kit Rating Plate accounts for high altitude

derate.

INSTALL ORIFICES

1. Install main burner orifices. Do not use Teflon tape. Fin-

ger-tighten orifices at least one full turn to prevent

cross-threading, then tighten with wrench.

2. There are enough orifices in each kit for largest furnace.

Discard extra orifices.

BURNER

"\ f ORIFICE BURNER

ORIFICE

A96249

Fig. 22 - Burner Orifice

Refer to conversion kit rating plate 337704-206 to determine

main burner orifice size. (See Fig. 23.)

Furnace gas input rate on furnace rating plate is for installations at

altitudes up to 2000 ft. (610 M).

In the U.S.A.; the input rating for altitudes above 2000 ft. (610

M) must be reduced by 2 percent for each 1000 ft. (305 M) above

sea level.

CONVERSION KiT RATING PLATE

NOTE: DO NOT reinstall the manifold at this time.

INSTALL MIXER SCREWS

NOTE: There are 2 sets of mixer screws. One set is for

Condensing gas furnaces, the other set is for Non-condensing gas

furnaces. Use only the parts in the bag marked "REQUIRED

FOR THE CONVERSION OF CONDENSING GAS

FURNACES TO PROPANE GAS"

See Fig. 24 to verify you have the correct set of mixer screws.

1. Locate the dimple on each burner venturi tube. If you can-

not locate the dimple, refer to Fig. 25 for location of the

mixer screw.

2. Drill a 7/64-in. (2.8 mm) hole (supplied in kit) in each

dimple.

3. Install a mixer screw in each drilled hole drilling as

straight as possible. The screw head should be flush with

the top of the burner venturi.

- CARRIER CORPORATION

THiS APPLIANCE HAS BEEN CONVERTED TO USE PROPANE GAS FOR FUEL. REFER TO KiT iNSTRUCTIONS FOR CONVERSION

PROCEDURES, USE PARTS SUPPLIED BY CARRIER CORPORATION AND iNSTALLED BY QUALIFIED PERSONNEL.

SEE EXiSTiNG RATING PLATE FOR APPLIANCE MODEL NO. AND iNPUT RATING.

NOTE: Furnace gas input rate on rating plate is for installations up to 2000 ft. (610m) above sea level, in U.S.A. the input rating for altitudes above2000 ft. (610m) must

be derated by 2%for each 1000 ft. (305m) above sea meveL mnCanada the input rating must be derated by 5%for altitudes of 2000 ft. (610m) to 4.500ft. (1372m) above sea meveL

KiT NO.: KGANP5201VSP (SUPERSEDES: NONE)

APPLIANCE

MODELS

59TN6A

986TA

PG96VAT

FUELUSED: PROPANEGAS NLETPRESSURE(min-max): 11.0-13.61n.wc

ALTITUDE OF iNSTALLATiON (FT. ABOVE SEA LEVEL) U.S.A. *

0 2001 * 3001 4001 5001 6001 7001 8001 9001

to 2000 to 3000 to 4000 to 5000 to 6000 to 7000 to 8000 to 9000 to 1OOOO

Orifice 1.25mm 1.25mm 1.25mm 1.25mm 1.25mm 1.25mm 1.25mm 1.25mm 1.25mm

No. Manifold Pressure

iHIGH 11.o ]11.o [ 11o _11.o I 11o [ 11o [ 11.o [ 11o [ 11.o

LOW 5.8 5.5 5.5 5.5 5.4 5.4 5.4 5.3 5.3

* For Canadian Installations from 2000 to 4500 ft. (610m to 1373m) use U.S.A. column 2001 to 3000 ft. (611m to 914m).

337704-206 REV. D

Al1635

Fig. 23 - Conversion Kit Rating Plate

[337932=701j

CONTAINS: QTY

PART # DESCRIPTION

328456-402 BIT, DRILL 1

FAJ5812B SCREW 7

REQUIRED FOR CONVERSION OF

CONDENSING GAS FURNACE TO

PROPANE GAS.

Fig. 24 - Gas Conversion Kit

Al1294

1.9"

(48.76 mm)

1.8"

(46.96 ram)

\\\\\

Fig. 25 - Mixer Screw Location

Drill out with

/64"drill bit

Al1460

1 2 ... 8 9 10 11 12 13 14 15 16 17 18 ... 25 26

Commentaires sur ces manuels

Pas de commentaire

Carrier KGANP5201VSP Manuel d'instructions Page 13

Commentaires sur ces manuels

Produits connexes et manuels pour Chauffe-eau et chaudières Carrier KGANP5201VSP